|
|
|
Who's Online
There currently are 5955 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
6gb33005.fm5 Page 35 Tuesday, September 11, 2001 9:53 AM
AFTER-SALES SERVICE
Before calling After-Sales Service
1. See if you can solve the problem yourself with the help of the �Troubleshooting guide�. Switch off the hood for a few minutes and re-start it 2. to see if the problem has cleared itself. 3. If the malfunction persists, call After-Sales Service. Specify: � the nature of the problem, � the model, � your full address, � your telephone number and area code. � The service code (number below the word SERVICE on the rating plate inside the hood behind the grease filter).
INSTALLATION
When installing the hood, the minimum distances from the cooktop must be respected, and the numerical sequence and additional instructions must be followed exactly as indicated on the Installation sheet.
External Exhaust Mode (A - see also installation sheet)
Cooking fumes and vapours are conveyed outside through a duct connected to the hood by means of a collar. The outlet duct diameter must be the same as that of the collar. If a flue-damper is to be installed, check that it can open and close freely when installation of the exhaust duct is complete. The hood can be supplied with one (upper) or two (upper and rear) exhaust outlet holes.
The hood is usually set up for using the upper exhaust outlet.
1. The collar must be seated in the upper exhaust outlet. Use the rear exhaust outlet (where present). 1. Where fitted, remove the cover closing off the rear outlet and collar. 2. Some models are fitted with a plastic deflector that closes off the rear outlet. If fitted, remove it. 3. Fit the collar in the rear outlet. 4. Put the cover (if fitted) in the upper outlet.
Warning! If the hood has a carbon filter, this should be removed.
Check that the switch inside the hood (if fitted) is in position �A� Extractor; if not, set it to this position.
Air Circulation Mode (F - see also installation sheet)
The air is filtered by a carbon filter and recycled into the surrounding atmosphere. The filtered air is released towards the kitchen ceiling. Check that the switch inside the hood (if fitted) is in position �F� Filter; if not, set it to this position. If the plug is provided, close off the upper exhaust hole.
Warning! If the hood does not have a carbon filter, order one and fit it before use.
Electrical connection
Before connecting the hood, make sure the voltage indicated on the rating plate corresponds to the voltage in your home. The plate is located inside the hood behind the grille. For GB this appliance is supplied without a plug and is intended for direct connection to fixed wiring in accordance with national wiring regulations. An all-pole disconnection switch with a minimum contact separation of 3 mm must be included in the fixed wiring in an easily accessible position. The Manufacturer shall not be liable for any damage or problem arising from the failure to comply with the above-mentioned instructions.
35
|
|
|
> |
|
