|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
;
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
;
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
;
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
;
I am happy to get a rare TECHNICS SH-9090 Owner's Manual by PDF in clear copy.
Whenthe control knobis turned ON, gas will flow intothe burner. The solid state igniter will click as long as the knob is in the Lite position. (Note: All burner igniters will spark regardlessof which burner is being operatedwhen a knob isturned to the Iite position.) A properly adjusted burner with clean ports will light within a few seconds. On natural gas, the flame will be blue with a deeper blue inner core. There should be no trace of yellow in theflame. A yellowflame indicatesan impropermixtureof air/gas. This wastes fuel, so havea servicemanadjust the mixtureif a yellow flame occurs. On LP gas, some yellow tipping is acceptable. This is normal and adjustment is not necessary. The infinite surface controls provide flexibility in heat setting selection. (See page 7,)
In case of prolonged powerfailure, youcan manuallylight the surfaceburner by holding a lightedmatchnearthe burnerportsand slowlyturningthe controlknobcounterclockwise (after depressing) to the LJte setting. CAI,ITION: When lightingthe surface burner, be sure all of the controlsare in the OFF position. Strike the matchfirst and hold it in position beforeturning the knobto the Lite position. Note: Becauseyour overhead hood fan is electricit will notwork during a power failure so smoke and condensationcan gather.
COUNTERCLO£;KWlSE
The Lo setting should produce a stable flame when turning the knob from Hi to Io. The flame should extend to the outer edge of the lip of theburner capon the Lo settingand must be stable on all ports on Lo setting. To adjust" Operate burner on Hi for about 5 minutes to preheat burner cap. Turn knob back to Lo; remove knob, and insert a small screwdriver into the center of the valve stem. Adjust flame size by turningadjustment screw in eitherdirection while holdingthe valve stem securely.
t TO,NCREASE _LAME _ _1 SLzE CLOCKW,SE.IIII A TO REDUCE FLAME SIZE
STEM
,
,
VALV W
Flame must be of sufficientsize to be stable on all burner ports. If flame adjustment is needed,adjust ONLY on the Lo setting. Never adjust flame size on a higher setting. Note: All gas adjustments should be done by a qualified servicer only. 6
|
|
|
> |
|