|
|
|
Who's Online
There currently are 5457 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Location Requirements
AIR PURIFIER CARE
Cleaning
1
1
1. A 20 cm min. clearance
Do not block the air openings or place the air puri�er on a soft surface such as a bed or sofa. Place air puri�er on a �at, level surface at least 20 cm from heat sources such as cookers or heaters. This product is intended for indoor use only.
2 3 4 5
AIR PURIFIER USE
Starting/Stopping Your Air Puri�er
NOTE: Before operating the air puri�er, record the date of installation on the HEPA �lter, which should be replaced annually under conditions of normal use and care. The pre-�lter should be replaced every 3 months. To remove and replace either �lter, see �Filter Replacement� in the �Air Puri�er Care� section.
1. Release tabs 2. HEPA �lter
3. Bottom slot 4. Pre-�lter
5. Front grille
1. Turn the fan speed knob to Off. 2. Unplug air puri�er or disconnect power. 3. Place �ngers on the front release tabs. Gently push the tabs in and pull the front grille forward to remove it. 4. Remove both �lters and set aside. NOTE: DO NOT try to wash and reuse either the HEPA �lter or the pre-�lter. 5. Clean the air puri�er with a soft, damp cloth. 6. Gently wash the front grille in soapy water. NOTE: The grille is not dishwasher safe. Be sure all parts are completely dry before reassembling them. 7. Reassemble the �lters as shown in the previous illustration. 8. Place the bottom tabs on the front grille into the slots in the base of the air puri�er. Push the top of the grille forward until the grille locks into place. 9. Plug in air puri�er or reconnect power. 10. Turn the fan speed knob to the desired fan speed.
1
Change HEPA Filter
4 5 6
2 3
Change Pre-Filter
Filter Reset
1. Low fan speed 2. Medium fan speed
3. High fan speed 4. HEPA �lter indicator light
5. Pre-�lter indicator light 6. Filter Reset button
1. Plug into a grounded (earthed) outlet. NOTE: Both �lter indicator lights will �ash once during a selftest when the air puri�er is turned on or after a power cut. 2. Turn the fan speed knob to the large fan icon (High), the middle fan icon (Medium) or the small fan icon (Low) to select the desired fan speed. 3. Turn the fan speed knob to Off to turn off the air puri�er.
3
|
|
|
> |
|
